Engine Specifications:
• HP: 205
• TQ: 280
• Block: OE block #327AB or 328AB
• Bore/Stroke: 3.915” or 3.935” x 3.895”
• Displacement: 4.6L / 4.7L
• Crankshaft: Scat nodular iron with .850” pilot hole
• Rods: OE
• Pistons: Hypereutectic 9.3:1 compression
• Rings: Moly
• Camshaft: Hyd. flat tappet
• Cam Specs: 206/212 @50 .462in/.478ex 113LSA
• Timing Chain: Single roller
• Cylinder Heads: OE cast iron #0331 1999-2006
• Rocker Arms: OE stamped steel
• Oil Pump: Melling standard volume

Recommended Components:
• Balancer: OE
• Flexplate/Flywheel: OE
• Intake Manifold: OE
• Throttle Body: OE
• Fuel Pump: OE
• Ignition: OE ignition system
• Spark Plugs: Autolite #AP985
• Spark Plug Wires: OE
• Water Pump: OE per application

Engine Info:
• Oil: Conventional / Non Synthetic 10W30 with Comp Cam zinc additive #159 for first 3000 miles
• Oil Filter: Wix or K&N
• Timing: Factory settings
• Spark Plug Gap: .035”
• Firing Order: 153624
• Octane: 91+
• Stall Converter: Stock
• Exhaust: Headers/Performance exhaust

Notes: This engine will work with all stock components, but ATK recommends a cold air intake, headers, exhaust and chip for maximum power potential.

Disclaimer: The parts listed are ATK’s recommendations of parts to be used to obtain our power figures listed. Power figures can vary based on parts used by the end user. It is the customer’s responsibility to verify components will work in their application. Some modifications to the vehicle may be required using these and or other aftermarket parts. . ATK reserves the right to substitute parts used in engines if necessary.

The post ATK HP67 Jeep 4.7L Street Stroker Base Engine 205HP for 99-06 Jeeps appeared first on ATK High Performance Engine.

Engine Specifications:
• HP: 205
• TQ: 280
• Block: OE block #569, 341 or 449
• Bore/Stroke: 3.915” or 3.935” x 3.895”
• Displacement: 4.6L / 4.7L
• Crankshaft: Scat nodular iron with .850” pilot hole
• Rods: OE
• Pistons: Hypereutectic 9.3:1 compression
• Rings: Moly
• Camshaft: Hyd. flat tappet
• Cam Specs: 206/212 @50 .462in/.478ex 113LSA
• Timing Chain: Single roller
• Cylinder Heads: OE cast iron #630 1996-1999
• Rocker Arms: OE stamped steel
• Oil Pump: Melling standard volume

Recommended Components:
• Balancer: OE
• Flexplate/Flywheel: OE
• Intake Manifold: OE
• Throttle Body: OE
• Fuel Pump: OE
• Ignition: OE ignition system
• Spark Plugs: Autolite #AP985
• Spark Plug Wires: OE
• Water Pump: OE per application

Engine Info:
• Oil: Conventional / Non Synthetic 10W30 with Comp Cam zinc additive #159 for first 3000 miles
• Oil Filter: Wix or K&N
• Timing: Factory settings
• Spark Plug Gap: .035”
• Firing Order: 153624
• Octane: 91+
• Stall Converter: Stock
• Exhaust: Headers/Performance exhaust

Notes: This engine will work with all stock components, but ATK recommends a cold air intake, headers, exhaust and chip for maximum power potential.

Disclaimer: The parts listed are ATK’s recommendations of parts to be used to obtain our power figures listed. Power figures can vary based on parts used by the end user. It is the customer’s responsibility to verify components will work in their application. Some modifications to the vehicle may be required using these and or other aftermarket parts. . ATK reserves the right to substitute parts used in engines if necessary.

The post ATK HP24 Jeep 4.7L Street Stroker Base Engine 205HP for 91-98 appeared first on ATK High Performance Engine.

Engine Specifications:
• HP: 205
• TQ: 280
• Block: OE block #535 or 665
• Bore/Stroke: 3.915” or 3.935” x 3.895”
• Displacement: 4.6L / 4.7L
• Crankshaft: Scat nodular iron with .850” pilot hole
• Rods: OE
• Pistons: Hypereutectic 9.3:1 compression
• Rings: Moly
• Camshaft: Hyd. flat tappet
• Cam Specs: 206/212 @50 .462in/.478ex 113LSA
• Timing Chain: Single roller
• Cylinder Heads: OE cast iron #686 1987-1990
• Rocker Arms: OE stamped steel
• Oil Pump: Melling standard volume

Recommended Components:
• Balancer: OE
• Flexplate/Flywheel: OE
• Intake Manifold: OE
• Throttle Body: OE
• Fuel Pump: OE
• Ignition: OE ignition system
• Spark Plugs: Autolite #AP3924
• Spark Plug Wires: OE
• Water Pump: OE per application

Engine Info:
• Oil: Conventional / Non Synthetic 10W30 with Comp Cam zinc additive #159 for first 3000 miles
• Oil Filter: Wix or K&N
• Timing: Factory settings
• Spark Plug Gap: .035”
• Firing Order: 153624
• Octane: 91+
• Stall Converter: Stock
• Exhaust: Headers/Performance exhaust

Notes: This engine will work with all stock components, but ATK recommends a cold air intake, headers, exhaust and chip for maximum power potential.

Disclaimer: The parts listed are ATK’s recommendations of parts to be used to obtain our power figures listed. Power figures can vary based on parts used by the end user. It is the customer’s responsibility to verify components will work in their application. Some modifications to the vehicle may be required using these and or other aftermarket parts. . ATK reserves the right to substitute parts used in engines if necessary.

The post ATK HP25 Jeep 4.7L Street Stroker Base Engine 205HP for 87-90 Jeeps appeared first on ATK High Performance Engine.